|
Pond Pump and Fountain |
Suitable for small garden fountains, piped statuary, and shallow water conditions, the PondMaster MD1.5 is a 140 GPH Submersible Pump. It has a 3/8 inch or 1/2 inch discharge, 120V 6' 3-prong grounded power cord, built-in adjustable flow control and foam pre-filter included. It can be used in a horizontal or vertical position and consumes a maximum of 9 Watts of power. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 1 Year Limited Manufacturer's Warranty. More Info...
Service and Maintenance: The housing should occasionally be removed to clean and inspect the impellor assembly. The impellor is the only serviceable item and can be pulled out of the body. Do not take the impellor apart. If it is worn or broken the entire impellor assembly should be replaced. This will restore the pump to original capacity. Pumps taken out of service for an extended period with fluid inside run the risk of forming a crust which may prevent subsequent starting. Saltwater should be flushed out with fresh water. Always check cord for sharp bends which can cause premature cracking. Do not use power cord to lift or move pump.
Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster MD1.9 is a 190 GPH Submersible Pump with a 3/8 in. or 1/2 in. discharge, a 10' 3-prong grounded power cord, a ceramic shaft and elbow included. It is fully submersible, very powerful, and can be used in a horizontal or vertical position. It consumes a maximum of 19 Watts with a built-in adjustable flow control and a foam pre-filter included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...
Service and Maintenance: Periodically the pump will need to be cleaned when the flow slows down or stops. To clean, unplug and remove from water. Slide off pre-filter cover and wash out foam pre-filter pad. After repeated washing, the foam will need to be replaced. After a period of time, deposits may build up inside the pump cover. Remove the four screws which hold the pump cover to the motor housing. The impellor is the only serviceable item. It can be pulled out and cleaned. If it is worn or broken the entire impeller assembly can be replaced. This will restore the pump to original capacity. Do not over tighten screws during reassembly. Check that O-ring is seated into grove in pump cover. If pump fails to start, recheck that impellor is not blocked by debris. For best results the minimum water level depth should be 2 inches. Pumps taken out of service with the fluid inside run the risk of forming a crust which may prevent subsequent start. The pump should be flushed out with fresh water. Always check cord for sharp bends which can cause premature cracking. Do not lift the pump with the cord. Running the pump in chlorine or bleach solution is not recommended. Do not allow the pump to run dry.
Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster PM2 is a 250 GPH Submersible Pump with a 1/2 inch MNPT discharge and 1/2 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord and operates submerged or in-line consuming a maximum of 24 Watts. A ceramic shaft and foam pre-filter are included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...
Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster PM3 is a 350 GPH Submersible Pump with a 1/2 inch MNPT discharge and 1/2 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord and operates submerged or in-line consuming a maximum of 35 Watts. A ceramic shaft and foam pre-filter are included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...
Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster PM5 is a 500 GPH Submersible Pump with a 1/2 inch MNPT discharge and 1/2 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord and operates submerged or in-line consuming a maximum of 45 Watts. A ceramic shaft and foam pre-filter are included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...